Indesit LVTI 12-67 Instruction for Use download pdf (Page 21)

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned to

the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher, making

it level. In any case, the appliance should not be inclined

more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

Adjustment of Back Feet

Insert the appliance in the cutout and then adjust the height

of the machine using the screws located at the bottom front.

Use a screwdriver to turn the screws in the clockwise direction

to raise the dishwasher and in the anticlockwise direction to

lower it.

Cold Water Connection

This electric household appliance should be connected to

the water mains using the cold water supply hose provided

with the appliance only. Do not use a different hose. In the

event of replacements, use original spare parts only.

Connect the cold water supply hose to a threaded 3/4 (gas)

connector and make sure that it is fastened tightly in place.

If the water pipes are new or have not been used for an

extended period of time, let the water run to make sure that

the water is clear and free of impurities. If this precaution is

not taken, there is a risk that the water inlet can get blocked

and damage the appliance.

Hot Water Connection

The water supply to the appliance can also be connected to

the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of 60°

In this case, the wash cycle time will be shortened by about

15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the cold

water line.

Anti-Flooding Protection

Your dishwasher is provided with a special system which

blocks the water supply in the event of leaks inside the

appliance. It is further equipped with a water inlet hose

comprising an outer clear hose and an inner red hose, which

can both withstand extremely high pressures. Should the inner

hose break, the outer hose will consequently turn red. Safety

in the event of flooding is ensured by the second clear hose

that contains the former. It is vital that you check the outer

hose regularly: if you see it has turned bright red, then you

know you have to replace it as soon as possible. Call for an

authorised technical engineer to come and replace it.

Drain Hose Connection

Fit the drain pipe into a drain

line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. The part of the

pipe marked with the letter A

s hould be between 40 and

100 cm above the ground.

The pipe should not be

immersed in water.

Electrical Connection

After making sure that the voltage and frequency values for

the current in the home correspond to those on the rating

plate (located on the stainless steel inner door of the

appliance) and that the electrical system is sized for the

maximum voltage on the rating plate, insert the plug into

an electrical socket which is earthed properly (the earthing

of the appliance is a safety requirement mandated by law).

If the electrical socket to which the appliance must be

connected is not appropriate for the plug, replace the plug,

rather than using adpators or the like as they could cause

overheating and burns.

Should the electricity supply cable be damaged, we

recommend that you only contact authorised Technical Service

Centres for the replacement.

CAUTION

The dishwasher plug must be accessible even when the

appliance is installed as a built-in unit so that maintenance

can be done safely.

Condensation-proof tape.

On some models, a transparent condensation-proof adhesive

tape has been provided.

It should be stuck onto the lower side of your wooden worktop

to protect it from the formation of condensation.

When not provided, this tape can be requested as a spare

part from authorised retailers.

1 ... 20 21 22 ... 52

Comments to this Manuals

No comments

Indesit LVTI 12-67 Instruction for Use Page 21

Comments to this Manuals

Related products and manuals for Dishwashers Indesit LVTI 12-67