Indesit PIM-604-(IX) User Manual download pdf (Page 18)

• Open the terminal box by removing the screws “V” and

opening the cover (see gure).

• Connect the wires as shown in the diagram.

• Fix the cable using the cable clamp “F”, replace the cover

and fasten it using the screws “V” (see gure).

1 2 3 4 5

1 2

12345

380-400V 3N~

H05RR-F 5x1.5 CEI-UNEL 35363

380-400V 2N~

H05RR-F 4x1.5 CEI-UNEL 35363

220-230V 1N~

H05RR-F 3x2.5 CEI-UNEL 35363

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate.

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

mains. The circuit-breaker must be suitable for the charge

indicated and must comply with current electrical regulations

(the earthing wire must not be interrupted by the circuit-

breaker). The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant with

safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these safety

measures not be observed.

! If the appliance is to be installed above a built-in electric

oven, the electrical connection of the hob and the oven must

be carried out separately, both for electrical safety purposes

and to make extracting the oven easier.

Electrical

connections

DATA PLATE

Voltage 220-230V/380-400V 3N ~ 50/60 Hz

Max power 7000 W

This appliance conforms to the following

European Economic Community directives:

- 2006/95/EEC dated 12/12/06 (Low Voltage)

and subsequent amendments

- 2004/108/EEC dated 15/12/04

(Electromagnetic Compatibility) and

subsequent amendments

- 93/68/EEC dated 22/07/93 and subsequent

amendments.

- 2012/19/EC and subsequent amendments.

Start-up and use

! The position of the corresponding electric hotplate is shown

on every knob.

Electric hotplates

The corresponding knob may be turned clockwise or anti-

clockwise and set to six different positions:

Setting Normal o Fast Plate

0 Off

Low

2-5 Medium

6 High

! Please refer to the “Practical advice on using the

appliance” section for a list of the relative positions and

their recommended uses.

Practical advice on using the electric

hotplates

To avoid heat loss and damage to the hotplates, use pans

with a at base, whose diameter is no less than that of the

hotplate itself.

Setting

Off

Cooking vegetables, fish

Cooking patatoes (using steam) soups,

chickpeas, beans.

Continuing the cooking of large quantities of

food, minestrone.

For roasting (average)

For roasting (above average)

For browning and reaching a boil in a short time

! Before using the hotplates for the rst time, you should heat

them at maximum temperature for approximately 4 minutes,

without placing any pans on them. During this initial stage, their

protective coating hardens and reaches its maximum resistance.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 47 48

Comments to this Manuals

No comments

Indesit PIM-604-(IX) User Manual Page 18

Comments to this Manuals

Related products and manuals for Hobs Indesit PIM-604-(IX)