Indesit PZ 750 R GH N /HA Instruction for Use download pdf (Page 15)

These pipes must be installed so that they are never

longer than 2000 mm when fully extended. Once

connection has been carried out, make sure that the

flexible metal pipe does not touch any moving parts and

is not compressed.

 Only use pipes and seals that comply with current

national regulations.

Checking the tightness of the connection

 When the installation process is complete, check the

pipe fittings for leaks using a soapy solution. Never use a

flame.

Adapting to different types of gas

To adapt the hob to a different type of gas other than

default type (indicated on the rating plate at the base of

the hob or on the packaging), the burner nozzles should

be replaced as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner,

and replace them with nozzles for the new type of gas

(see table 1 Burner and nozzle characteristics).

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

Replacing the nozzles on se

parate double flame 

burners:

1. remove the grids and slide the burners from their

housings. The burner consists of 2 separate parts (see

figure);

2. unscrew the burers with a 7 mm wrench spanner. The

internal burner has a nozzle, the external burner has

two (of the same size). Replace the nozzle with models

suited to the new type of gas (see table 1).

3. replace all the components by repeating the steps in

reverse order.

 Adjusting the burners primary air :

Does not require adjusting.

 Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust

the adjustment screw, which is

positioned in or next to the tap

pin, until the flame is small but

steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position of

the knob from minimum to maximum and vice versa

several times, checking that the flame does not go out.

4. Some appliances have a safety device (thermocouple)

fitted. If the device fails to work when the burners are set

to the low flame setting, increase this low flame setting

using the adjusting screw.

5. Once the adjustment has been made, replace the seals

on the by-passes using sealing wax or a similar

substance.

 The DCDR burner tap is fitted with 2 minimum adjustment

screws: one is located alongside the pin for the external

DCDR, while the other is inside the pin for the internal

DCDR.

 If the appliance is connected to liquid gas, the regulation

screw must be fastened as tightly as possible.

 Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

 Should the gas pressure used be different (or vary slightly)

from the recommended pressure, a suitable pressure

regulator must be fitted to the inlet pipe (in order to comply

with current national regulations).

DATA PLATE

Electrical

connections

voltage of 220-240V ~ 50/60Hz

(see data plate )

This appliance conforms to the

following European Economic

Community directives:

-2006/95/EEC dated 12/12/06 (Low

Voltage) and subsequent

amendments

- 2004/108/EEC dated 15/12/04

(Electromagnetic Compatibility)

and subsequent amendments

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 90/336/EEC dated 29/06/90 (Gas)

and subsequent amendments.

- 2002/96/EC and subsequent

amendments.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 43 44

Comments to this Manuals

No comments

Indesit PZ 750 R GH N /HA Instruction for Use Page 15

Comments to this Manuals

Related products and manuals for Hobs Indesit PZ 750 R GH N /HA