22
EN
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
Troubleshooting
0DOIXQFWLRQ 3RVVLEOHFDXVHV6ROXWLRQV
7KHGLVKZDVKHUGRHVQRWVWDUW
• The plug has not been inserted into the electrical socket
properly, or there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (
see Start-up and use
).
1RZDWHUHQWHUVWKHGLVKZDVKHU
• There is no water in the mains supply.
• The water inlet hose is bent (
see Installation
).
1RZDWHUGUDLQVRXWIURPWKH
GLVKZDVKHU
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (
see Installation
).
• The drain duct is blocked.
• The filter is clogged up with food residues.
7KHGLVKZDVKHUPDNHV
H[FHVVLYHQRLVH
• The dishes are rattling against each other or against the
sprayer arms.
7KHGLVKHVDQGJODVVHVDUH
FRYHUHGLQDZKLWHILOPRU
OLPHVFDOHGHSRVLWV
• The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (
see Rinse aid and salt
).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
7KHGLVKHVDQGJODVVHVDUH
VWUHDNHGRUKDYHDEOXLVK
WLQJH
• The rinse aid dosage is too high.
7KHFURFNHU\KDVQRWEHHQGULHG
SURSHUO\
• The rinse aid has been used up or the dosage is too low (
see
Rinse aid and salt
).
• The rinse aid dispenser setting is not high enough.
• A wash cycle without a drying programme has been selected.
7KHGLVKHVDUHQRWFOHDQ
• The racks are overloaded (
see Loading the racks
).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (
see Wash cycles
).
• The detergent has not been measured out correctly or it is not
suited to the type of wash cycle (
see Start-up and use
).
• The filter is dirty or blocked (
see Care and maintenance
).
• The refined salt level is low (
see Rinse aid and salt
).
6KXWRIIWDSDODUP
(several short beeps are emitted)
(the 2
nd
and 3
rd
WASH CYCLE in
progress indicator lights flash).
• Turn on the tap and the appliance will start after a few
minutes.
• The appliance lock has been activated because no action was
taken when the beeps sounded. Switch off the machine using
the ON/OFF button, turn on the tap and switch the machine
back on after 20 seconds by pressing the same button. Re-
programme the machine and
restart the wash cycle.
%ORFNHGILOWHUDODUP
(the 1
st
and 3
rd
WASH CYCLE in
progress indicator lights flash).
• Switch off the machine by pressing the ON/OFF button and
clean the filters (
see Maintenance
), then switch the
dishwasher back on by pressing the same button. Re-
programme the machine and restart the wash cycle.
:DWHUORDGLQJVROHQRLGYDOYH
PDOIXQFWLRQDODUP
(the 2
rd
WASH CYCLE in
progress indicator light flashes).
• Switch off the appliance by pressing the ON/OFF button and
switch it back on after a minute. If the alarm continues, turn
off the water tap to reduce the risk of flooding, remove the
plug from the electrical socket and call Assistance.
Comments to this Manuals