Indesit PC 640 N T X AUS Instruction for Use download pdf (Page 8)

• Cabinets installed adjacent to the hood must be at least

420 mm above the hob,

The following minimum clearances

to combustible materials must be

observed:

• Minimum clearance from edge

of burner to side wall must be 200

mm.

• Minimum clearance from edge of

burner to rear wall must be 55 mm.

Range hoods

Range hoods and overhead exhaust fans must be installed

according to manufacturers’ instructions but in no case shall

clearance from hob burners be less than 650 mm for range

hoods and 750 mm for overhead exhaust fans.

• If the hood is installed below a wall cabinet, the latter

must be at least 700 mm (millimetres) above the surface

of the hob.

Fitting the cooktop above an oven

When installing the cooktop above an oven, both the

electricity supply cable and the gas pipe or exible hose

must not touch hot parts of the oven housing.

When installing above a built-under oven without forced

cooling ventilation, suitable air vents should be provided for

(inlet at least 200 cm² from the bottom, outlet at least 120

cm² from the top part) to allow adequate ventilation inside

the housing unit.

Also a wooden panel should be installed beneath the hob

as insulation, positioning it at a minimum distance of 15 mm

from the hob housing.

Before the installation remove the grids and burners from

the hob and turn it upside down, making sure you don’t

damage the thermocouples and spark plugs.

Apply the seals that come with

the appliance along the outer

edges of the hob to prevent any

passage of air, humidity and

water (see Figure).

For proper application make sure the surfaces to be sealed

are clean, dry and free of any grease/oil.

• The installation cavity should have the dimensions

indicated in the gure. Fastening hooks are provided,

allowing you to fasten the hob to tops that are between 20

and 40 mm thick. To ensure the hob is securely fastened

to the top, we recommend you use all the hooks provided.

555 mm

55 mm

475 mm

600mm min.

420mm min.

650mm min.

Hook fastening diagram

Hooking position Hooking position

for top H=20mm for top H=30mm

Front

Hooking position Back

for top H=40mm

! Use the hooks contained in the “accessory pack”.

• Where the hob is not installed over a built-in oven, a

wooden panel must be installed as insulation. This must

be placed at a minimum distance of 20 mm from the lower

part of the hob.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet

must be removed. It is advisable to install the oven so that it

rests on two strips of wood, or on a completely at surface

with an opening of at least 45 x 560 mm (see diagrams).

560 mm.

45 mm.

Electrical connection

Hobs equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage and

frequency indicated on the data plate (this is located on the

lower part of the appliance). The earth wire in the cable has a

green and yellow cover. If the appliance is to be installed above

a built-in electric oven, the electrical connection of the hob and

the oven must be carried out separately, both for electrical

safety purposes and to make extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate.

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

AUS

1 2 3 4 5 6 7 8 9 ... 28

Comments to this Manuals

No comments

Indesit PC 640 N T X AUS Instruction for Use Page 8

Comments to this Manuals

Related products and manuals for Hobs Indesit PC 640 N T X AUS