Indesit KBM 6004 CL Instruction for Use download pdf (Page 21)

Technical characteristics

Electrical connection

• The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently

earthed, in compliance with regulations on electrical

safety. Always ensure that this vital safety measure has

been taken. If you have any doubts, call in a qualified

technician to check the electrical system thoroughly.

•

The manufacturer denies all responsibility for dam-

age resulting from a system which has not been

earthed correctly.

• Before powering the appliance, check whether the

technical characteristics featured on the appliance data

plate correspond with those of the mains electrical

system.

• Check that the current load of the mains supply and

of the power sockets is suitable for the maximum power

of the appliance, indicated on the appliance data plate.

If in doubt, contact a qualified professional.

Disconnect the appliance from the electricity supply

before all operations.

Connect your hob to the electrical system by means of a

junction box: if the appliance is connected permanently

to the mains, an omnipolar circuit breaker, accessible if

necessary, with a minimum contact opening of 3 mm

should be installed.

Single-phase connection

The hob is equipped with a preconnected electricity sup-

ply cable, which is designed for single-phase connection.

Connect the wires according to the instructions given in

the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

230V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 230V 3 ~ 50 Hz

• 400V - 2+2N ~ 50 Hz

Separate the wires and connect them according to the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V 3 - N ~ 50 Hz

proceed as follows:

! The cable provided is not suitable for the following types

of installation.

1. Use a suitable supply cable, H05RR-F or higher, with

the right dimensions (cable section: 2.5 mm).

2. To open the terminal board, insert a screwdriver into

the side tabs of the cover and open it (

see Terminal board

picture

3. Loosen the cable clamp screw and the terminal board

screws according to the type of connection required and

position the connection supports as shown in the follow-

ing table and diagrams.

4. Position the wires according to the following table and

diagrams and connect the appliance by tightening all the

screws for the springs as much as possible.

Voltage and

mains frequency

Electrical connections Terminal board

400V 3-N ~ ı 50

Three-phase 400

5. Secure the power supply cable by fastening the cable

clamp screw, then put the cover back on.

U-bolt

connection support

Phase PhasePhase Neutral Earth

Three-phase 400

This appliance conforms with the following European

Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic

compatibility) and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments;

- 2002/96/EC

Warning: If the hob is fitted above a built-in oven, the hob

and the oven must be connected to the mains separately for

safety reasons and to simplify operations when it is necessary

to pull the oven out for some reason.

1 ... 20 21 22 ... 42

Comments to this Manuals

No comments

Indesit KBM 6004 CL Instruction for Use Page 21

Comments to this Manuals

Related products and manuals for Hobs Indesit KBM 6004 CL