Indesit B PP 73 G HA 240S GT Instruction for Use download pdf (Page 17)

Electrical connection

Hobs equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate (this is located

on the lower part of the appliance). The earth wire in the

cable has a green and yellow cover. If the appliance is to

be installed above a built-in electric oven, the electrical

connection of the hob and the oven must be carried out

separately, both for electrical safety purposes and to make

extracting the oven easier.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate.

The appliance must be directly connected to the mains

using an omnipolar circuit-breaker with a minimum contact

opening of 3 mm installed between the appliance and the

mains. The circuit-breaker must be suitable for the charge

indicated and must comply with current electrical regulations

(the earthing wire must not be interrupted by the circuit-

breaker). The supply cable must not come into contact with

surfaces with temperatures higher than 50°C.

! The installer must ensure that the correct electrical

connection has been made and that it is compliant with

safety regulations.

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

Gas connection

• Check that the appliance is set for the type of gas

available and then connect it to the mains gas

piping or the gas cylinder in compliance with

current regulations and standards.

• This appliance is designed and set to work with the

gas indicated on the label situated on the actual

hob. If the gas supply is other than the type for

which the appliance has been set, proceed with

replacing the corresponding nozzles (provided),

following instructions given in the paragraph

“Adaptation to different types of gas”.

• For trouble-free operation, suitable use of energy

and longer life of the appliance, make sure that the

supply pressure complies with the values indicated

in the table 1 "burners and nozzles specifications,

otherwise install a special pressure regulator on the

supply pipe in compliance with current standards

and regulations.

• Connect in such a way that the appliance is

subjected to no strain whatsoever.

Either a rigid metal pipe with fittings in compliance

with the standards in force must be used for

connecting to the nipple union (threaded ½"G male

fitting) situated at the rear of the appliance to the

right (Fig.9), or flexible steel pipe in compliance with

the standards in force, which must not exceed 2000

mm in length. Should it be necessary to turn the

fitting, the gasket (supplied with the appliance) must

be replaced. Upon completion of installation, check

the gas circuit, the internal connections and the taps

for leaks using a soapy solution (never a flame). Also

check that the connecting pipe cannot come into

contact with moving parts which could damage or

crush it. Make sure that the natural gas pipe is

adequate for a sufficient supply to the appliance

when all the burners are lit

Important:Important:

Important: A pressure regulator, in compliance with

the standards in force, must be inserted when

connecting to a liquid gas supply (in a cylinder).

Adaptation to a different type of gas

If the hob is to be converted for use with a type of

gas other than that for which it was set in the factory

(indicated on the label to be found on the hob), the

burner nozzles should be replaced as follows:

• Remove the pan supports and the burners.

• Unscrew the nozzles “A” (Fig.10) using a 7 mm

socket wrench and replace them with the ones

which have a diameter suitable for the type of gas

to be used, according to the table 1 "burners and

nozzles specifications).

• On completing the operation, replace the old rating

which may vary according to the type of installation

required and the proportions of the appliance.

N.B.: to maximise the efficiency of all maintenance

operations, the area around the hob must be easily

accessible after it has been installed (i.e. there are no

completely shut-off elements).

1 ... 16 17 18 ... 76

Comments to this Manuals

No comments

Indesit B PP 73 G HA 240S GT Instruction for Use Page 17

Comments to this Manuals

Related products and manuals for Hobs Indesit B PP 73 G HA 240S GT